华为S9300问题

Question

我这边买了一个 s9306交换机 跟网通的思科路由器设备连接 用8条 小方口光线连接 分成2个组 每个组4根线 开OSPF 让他带宽达到8G
现在的问题是这样的 思科那边网通给调的他们告诉我调完了
现在我这边开了OSPF 上不去网 只能pING通思科设备谁能帮我看下怎么回事

[jssj01]dis cur
#
sysname jssj01
#
vlan batch 2
#
diffserv domain default
#
drop-profile default
#
interface Vlanif1
ip address 125.211.199.214 255.255.255.252
#
interface Vlanif2
ip address 125.211.199.218 255.255.255.252
#
interface Eth-Trunk1
port link-type access
#
interface Eth-Trunk2
port link-type access
port default vlan 2
#
interface Ethernet3/0/0
这些都没用我就省略下百度之让打1400多个字
interface Ethernet3/0/47
#
interface GigabitEthernet1/0/0
eth-trunk 1
undo negotiation auto
#
interface GigabitEthernet1/0/1
#
interface GigabitEthernet1/0/2
eth-trunk 1
undo negotiation auto
#
interface GigabitEthernet1/0/3
#
interface GigabitEthernet1/0/4
eth-trunk 1
undo negotiation auto
#
interface GigabitEthernet1/0/5
#
interface GigabitEthernet1/0/6
eth-trunk 1
undo negotiation auto
#
interface GigabitEthernet1/0/7
#
interface GigabitEthernet1/0/8
eth-trunk 2
#
interface GigabitEthernet1/0/9
#
interface GigabitEthernet1/0/10
eth-trunk 2
#
interface GigabitEthernet1/0/11
#
interface GigabitEthernet1/0/12
eth-trunk 2
#
interface GigabitEthernet1/0/13
#
interface GigabitEthernet1/0/14
eth-trunk 2
#
这些都没用我就省略下百度之让打1400多个字
#
interface GigabitEthernet2/0/47
#
interface NULL0
#
aaa
authentication-scheme default
#
authorization-scheme default
#
accounting-scheme default
#
domain default
#
#
ospf 88
maximum load-balancing 2
area 0.0.0.0
area 0.0.0.1
area 0.0.0.2
network 125.211.199.212 0.0.0.3
network 125.211.199.216 0.0.0.3
#
user-interface maximum-vty 15
user-interface con 0
idle-timeout 0 0
screen-length 0
user-interface vty 0 14
authentication-mode none
user privilege level 3
idle-timeout 0 0
screen-length 0
user-interface vty 16 20
#
return
[jssj01]disp ip routing-table
Route Flags: R - relay, D - download to fib
-----------------------
Routing Tables: Public
Destinations : 10 Routes : 10

Destination/Mask Proto Pre Cost Flags NextHop Interface

125.211.199.212/30 Direct 0 0 D 125.211.199.214 Vlanif1
125.211.199.214/32 Direct 0 0 D 127.0.0.1 InLoopBack0
125.211.199.215/32 Direct 0 0 D 127.0.0.1 InLoopBack0
125.211.199.216/30 Direct 0 0 D 125.211.199.218 Vlanif2
125.211.199.218/32 Direct 0 0 D 127.0.0.1 InLoopBack0
125.211.199.219/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

Answer 1

看路由表的话。路由信息没有学习到。
你做了2组的端口汇聚，首先判断端口汇聚是否成功，因为与cisco设备对联。可能有点问题。

如果端口汇聚成功了。
出现的问题就是ospf的问题。
area区域要和对方一致。具体的还是要和对方多沟通。
没看到你的设备有route id 。最好设置一下。